Skip to main content

Butterfly coaster set: How I made article 22

 This article is brought to you by Lizzsews.


In today's article, I will guide you through how I made a butterfly coaster set. Follow along with this project and share your result in Lizzsews Facebook group.


Recommended read: How I made article series


What I used:

- Square coaster

- Infusible ink lilac transfer sheets

- butcher paper

- Cricut

- EasyPress 2 + mat

- Cardstock

- Standardgrip mat


The steps I took:

I started out by looking for butterfly designs. I added white squares to my Cricut design space canvas that were 3.75" x 3.75" so I could see how the different designs would look on the coasters. I narrowed my selection down to four designs that I liked and that matched.

Cricut image ID: #M2AAB3D88- Square with rounded corners
Cricut image ID: #M369F6A19 - Butterfly on a Flower
Cricut image ID: #M249AOAFA - Butterflies
Cricut image ID: #MCB3D6C9 - Butterfly
Cricut image ID: #M33FB85O4 - Flowers And Butterfly

Recommended (design): Butterfly coasters set of 4


I resized each butterfly design to match the coaster size. I stuck the infusible ink to the standardgrip mat and used the Cricut brayer to secure it.

I removed the squares from the design, clicked 'make it', and mirrored the design.

Recommended read: Cricut when to mirror (and how)



Once cut, I weeded the design by peeling off the unnecessary pieces. This process was a little difficult and tedious, but so worth it. I find that using the Cricut weeder to gently hold down certain pieces while peeling off the unnecessary pieces helps. Before placing the design onto the cork-backed square coaster, I wiped down the coaster top with a lint-free cloth. Place the infusible ink design onto the coaster ink side down, liner side up.





I preheated my EasyPress 2 to 400°F. I used the Cricut heat guide to determine the temperature, the amount of time to press for and the pressure to press with. I placed a piece of cardstock on top of the EasyPress mat, placed the square coaster glossy side with the design up and a piece of butcher paper on top of everything. Inside of the infusible ink transfer sheets roll is a piece of butcher paper!


Next, I placed the EasyPress 2 onto everything and left it with no pressure for 60 seconds. Once the timer was up, I slowly lifted up the EasyPress 2. I waited until the liner was a little cooler to the touch to peel as it was very hot.


I repeated the same application steps for the other three coasters.

Each coaster came out great and I'm so happy with my butterfly coaster set!


Recommended read: Dancer hand towel embroidery: How I made article 21


Leave a comment below and let me know if you made this coaster set! And don't forget to subscribe to stay up to date with all of Lizzsews new articles. See you next time!

Comments

Popular posts from this blog

10 Things You Need To Start Machine Embroidery Today

This article is brought to you by Lizzsews Thinking about diving into machine embroidery but not sure where to start? Here’s everything you need to know to get started—without spending a fortune. Interested in sewing?  Recommended read: 10 Things You’ll Need to Start Sewing! 1. Get Yourself an Embroidery Machine You can start with any embroidery machine, but here are a few great beginner-friendly options: Brother SE600 – A combo machine that sews and embroiders. It’s affordable, versatile, and my top pick for beginners. Brother PE550D – Embroidery-only and comes with built-in Disney designs. Super cute! Brother SE1900 – A step up, with more advanced features and a larger embroidery area. 💡 Tip: Set a clear budget before buying, b uy the largest hoop your budget allows . While the SE600’s 4x4 hoop is great for starters, you may outgrow it quickly—and the next hoop size up is a big price jump. Recommended read: How to Choose the Right Embroidery Machine   ...

8 Reasons Why Your Upper Thread Is Shredding On Your Embroidery Machine

 This article is brought to you by  Lizzsews . Here are some reasons why your top thread might be shredding while you’re embroidering! Starting machine embroidery is definitely a challenge, and troubleshooting is hard.  Recommended read: 10 Things you need to start machine embroidery today Often when your top thread is shredding, it’s caused by when the thread goes through the eye of the needle or while it’s going through the thread guides.  1. A dull or bent needle How long has it been since you’ve changed that needle? It might be time to swap it out! A needle only lasts about 8-10 hours of stitching, this amount of time may vary depending on what you are making. It’s good to have lots of needles on hand. Recommended read: When should I change the needle for machine embroidery 2. Are you using the right needle for the project? Are you embroidering heavier fabrics? Like denim or leather? If so, you’ll want to use a heavier needle size like 90/14. If you’re just...

Guide To The Three Main Machine Embroidery Stabilizers

This article is brought to you by  Lizzsews . Here's everything you need to know about the three main types of machine embroidery stabilizers, what they're used for and how to pick the right one. 💡 Why Stabilizers Matter Stabilizers are essential in machine embroidery. They help support your fabric, prevent puckering , and ensure your design comes out clean and crisp. A stabilizer is placed underneath your fabric. Some special ones, called toppers , go on top, but these are only used for certain materials, like towels or blankets. 👉 You always need a bottom stabilizer. Toppers are optional and only used for specific projects. 🏷️ The 3 Main Types of Stabilizers 1. ✂️ Cutaway Stabilizer Cutaway stabilizer is non-woven , permanent, and ideal for stretchy or knit fabrics like t-shirts, baby onesies, and fleece. Why it's great: Provides strong support Prevents pulled or sagging stitches Stays put even after washing and wearing Comes pre-cut or in ro...