How I made article 7

This article is brought to you by Lizzsews.

In today's article, I will guide you through how I used iron-on vinyl to make a volleyball blanket. I’m not too sure how the design will last, the iron-on vinyl is sitting on top of the fibres of the blanket, where infusible ink would infuse ink into the blanket. Follow along with this project and share your result in Lizzsews Facebook group.

Recommended read: 10 Things You Need to Start Cricut Crafting Today
Recommended read: How I made article series

What I used:

- Iron-on vinyl

- Blanket

- Cricut

- Standardgrip mat

- EasyPress 2 + mat

The steps I took:

To make this volleyball blanket, I used these two Cricut designs:

-> Text: #MBE29F99

-> Diver: #M8B60CDF

I mirrored by design and cut out the iron-on vinyl. After cutting, I weeded the design.

Recommended read: When to mirror and how

With my Easypress 2 at 315 degrees, I pressed the blanket for 5 seconds.

I placed the diving volleyball player where I wanted it in the corner and pressed for 30 seconds, flipped and pressed for 15 seconds then peeled off the liner. Next, I placed parchment paper on top of the design and just pressed for a couple extra seconds.

I then repeated the same steps for the words but on the top left corner.

Recommended read: Phone holder: How I made article 6
Recommended read: Compost bin: How I made article 8

Leave a comment below and let me know if you made this volleyball blanket! Don't forget to subscribe to get notified for my next blog post :)

Comments

10 Things You Need To Start Machine Embroidery Today

This article is brought to you by Lizzsews . How to start machine embroidery! Here’s everything that you need to get started with machine embroidery! Without spending too much! Are you interested in sewing? Recommended read: 10 things you'll need to start sewing! 1. You are going to need an embroidery machine . You can use any embroidery machine you want. Here are a couple of examples: The Brother se600. This machine can do both sewing and embroidery, and is the best budget embroidery machine! I highly suggest this machine. The brother pe550D! This is an embroidery-only machine, with awesome Disney embroidery designs! The brother se1900. I recommend the Brother brand for sewing and embroidery machines. To note here: determine your budget, determine how much you have to spend on embroidery supplies (and blanks ) and how much you have to spend on your machine. Purchase the largest embroidery hoop that you can afford! The se600 is an amazing machine and I highly recomm

8 Reasons Why Your Upper Thread Is Shredding On Your Embroidery Machine

This article is brought to you by Lizzsews . Here are some reasons why your top thread might be shredding while you’re embroidering! Starting machine embroidery is definitely a challenge, and troubleshooting is hard. Recommended read: 10 Things you need to start machine embroidery today Often when your top thread is shredding, it’s caused by when the thread goes through the eye of the needle or while it’s going through the thread guides. 1. A dull or bent needle How long has it been since you’ve changed that needle? It might be time to swap it out! A needle only lasts about 8-10 hours of stitching, this amount of time may vary depending on what you are making. It’s good to have lots of needles on hand. Recommended read: When should I change the needle for machine embroidery 2. Are you using the right needle for the project? Are you embroidering heavier fabrics? Like denim or leather? If so, you’ll want to use a heavier needle size like 90/14. If you’re just embroidering mid-weight

Guide To The Three Main Machine Embroidery Stabilizers

This article is brought to you by Lizzsews . Here is everything that you need to know about the three main machine embroidery stabilizers. Stabilizers are important in machine embroidery; they prevent puckering and support the fabric. The stabilizer goes underneath the fabric you are embroidering. Although there are some stabilizers that will go on top of certain types of fabric, this is called a topper. A bottom stabilizer is always needed, you can never embroider without stabilizer, but a stabilizer topper is only needed for certain blanks. The three main types of stabilizers are cutaway, tearaway, and wash away. The first is a cutaway stabilizer. A cutaway stabilizer can be used on clothes and many different types of fabric. The cutaway stabilizer is permanent and is mainly designed for knit fabric. It is non-woven and helps get rid of pulled or sagging stitches. The cutaway stabilizer has a lot of stretch resistance and stays intact after wearing, using, and launderin

Lizzsews

Search This Blog