Skip to main content

How to embroider Lego Baby Yoda with rectangle appliqué

By Lizzsews

 This article is brought to you by Lizzsews.

Here’s how you can embroider out Lego baby Yoda inside of a rectangle with appliqué fabric!


What you will need:


The steps: 


   1. Hoop your fabric and stabilizer 


Recommended read: How to hoop fabric for machine embroidery


   2. On your machine select the rectangle design, choose the one with a satin stitch that goes around. 



   3. But before using the one with a satin stitch, begin with the outline, #10 in rectangles on the Brother se600. 


Recommended read: Brother se600 review


I changed the colour of my rectangles to #507 emerald green and resized them. I also resized my outline rectangle to 59.8 mm x 94.4 mm


   4. Stitch out the outline rectangle. 


   5. Place your appliqué fabric on top of this outline and stitch out the outline again. 



Cut around the fabric as close to the stitching as you can. Appliqué scissors may help.


   6. Stitch out the satin stitch rectangle. I resized my satin stitch rectangle to 62.7 mm x 98.2 mm



   8. Stitch out Lego Baby Yoda.



Feel free to keep your Lego Baby Yoda colours the same, but I adjusted mine and replaced #900 black with #707 dark grey and #001 white with #1618 snow white. 


Your appliqué is complete!


Recommended read: How to sew a pillowcase


Leave a comment below and let me know if you did this appliqué! And don't forget to subscribe to stay up to date with all of Lizzsews new articles. See you next time!



Labels:

Comments

Post a Comment

Popular posts from this blog

10 Things You Need To Start Machine Embroidery Today

By Lizzsews
 This article is brought to you by  Lizzsews . How to start machine embroidery! Here’s everything that you need to get started with machine embroidery! Without spending too much! Are you interested in sewing? Recommended read:  10 things you'll need to start sewing! 1. You are going to need an embroidery machine . You can use any embroidery machine you want. Here are a couple of examples: The Brother se600. This machine can do both sewing and embroidery, and is the best budget embroidery machine! I highly suggest this machine. The brother pe550D! This is an embroidery-only machine, with awesome Disney embroidery designs! The brother se1900. I recommend the Brother brand for sewing and embroidery machines. To note here: determine your budget, determine how much you have to spend on embroidery supplies (and blanks ) and how much you have to spend on your machine. Purchase the largest embroidery hoop that you can afford! The se600 is an amazing machine and I hig...
5 comments
Read more

8 Reasons Why Your Upper Thread Is Shredding On Your Embroidery Machine

By Lizzsews
 This article is brought to you by  Lizzsews . Here are some reasons why your top thread might be shredding while you’re embroidering! Starting machine embroidery is definitely a challenge, and troubleshooting is hard.  Recommended read: 10 Things you need to start machine embroidery today Often when your top thread is shredding, it’s caused by when the thread goes through the eye of the needle or while it’s going through the thread guides.  1. A dull or bent needle How long has it been since you’ve changed that needle? It might be time to swap it out! A needle only lasts about 8-10 hours of stitching, this amount of time may vary depending on what you are making. It’s good to have lots of needles on hand. Recommended read: When should I change the needle for machine embroidery 2. Are you using the right needle for the project? Are you embroidering heavier fabrics? Like denim or leather? If so, you’ll want to use a heavier needle size like 90/14. If you’re just...
Post a Comment
Read more

Guide To The Three Main Machine Embroidery Stabilizers

By Lizzsews
 This article is brought to you by  Lizzsews . Here is everything that you need to know about the three main machine embroidery stabilizers. Stabilizers are important in machine embroidery; they prevent puckering and support the fabric.  The stabilizer goes underneath the fabric you are embroidering. Although there are some stabilizers that will go on top of certain types of fabric, this is called a topper.  A bottom stabilizer is always needed, you can never embroider without stabilizer, but a stabilizer topper is only needed for certain blanks. The three main types of stabilizers are cutaway, tearaway, and wash away.  The first is a cutaway stabilizer. A cutaway stabilizer can be used on clothes and many different types of fabric. The cutaway stabilizer is permanent and is mainly designed for knit fabric. It is non-woven and helps get rid of pulled or sagging stitches.  The cutaway stabilizer has a lot of stretch resistance and stays intact after ...
1 comment
Read more